AMSYS

blankNews


aktivPressure Sensors

blankProductfinder

blankAbsolute
blankRelative
blankDifferential
blankBidirectional
blankBarometric
blankAccessory
blankCustomized Sensors

blankMeasuring Cells
aktivHumidity Sensors
blankTemperature Sensors
blankMagneto Sensors
blankInclinometer


blankApplications
blankDownload
blankCompany


blankContact

AMSYS Pressure Sensor Accessory

Starter Kits and Evaluation Boards

Caps for Pressure Sensors

Housing

Cable



Starter Kits and Evaluation Boards

BB AMS 5812
Starter Kit for Pressure sensor AMS 5812

The USB Starter Kit AMS 5812 is designed for quick and easy initial operation of AMS 5812 pressure sensors with I²C interface. Together with a standard PC with Windows operating system and the relevant software, the kit enables current digital pressure and temperature values to be read out via the AMS 5812 I²C sensor interface and to be displayed on the PC. In addition the starter kit can be used to program a second individual I²C address into each AMS 5812 pressure sensor. This customized I²C address is prerequisite for the operation of several AMS 5812 pressure sensors together on one I²C bus. This address is valid in addition to the default I²C address 78hex.

User Guide Starter kit AMS 5812
BB AMS 5105
Starter Kit for Pressure switch AMS 5105

The USB Starter Kit AMS 5105 is designed for easy individual configuration and adjustment of the two switching outputs of AMS 5105 pressure sensor/ pressure switch using a standard PC with USB interface. Together with the relevant software the customer can configure the two independent switching outputs of the AMS 5105 as normally open, normally close or in window mode and can adjust the specific thresholds, hysteresis and switching delays for both switching outputs individually. In addition it is possible to display the AMS 5105 internal calculated corrected digital pressure and temperature values for analysis purpose using the starter kit software.

User Guide Starter kit AMS 5105
BB AMS 5915 Starter Kit for Pressure sensor AMS 5915

The USB Starter Kit AMS 5915 is designed for quick and easy initial operation of AMS 5915 pressure sensors with a standard PC with Windows operating system. Without additional components, the kit enables current digital pressure and temperature values to be read out via the I²C sensor interface and to be displayed on the PC. In addition the starter kit can be used to program an individual I²C address into each AMS 5915 pressure sensor. This customized I²C address is prerequisite for the operation of several AMS 5915 pressure sensors together on one I²C bus.

User Guide Starterkit AMS 5915
Development Kit Development Kit for MEAS Switzerland pressure sensors

The MEAS Switzerland pressure sensor evaluation kit: an USB connector hardware module & data monitoring / recording solution.

Features
  • 10 - 1100 mbar absolute pressure range
  • USB interface
  • Recording software compatible with windows XP / VISTA
  • RoHS-compatible & Pb-free
  • Flash software upgradeable through USB
Software
The accompanying software allows fast data monitor and recording on your pc of the atmospheric pressure and ambient temperature at speeds up to 25 times/seconds.

Hardware
Exists in standard demo version with a MS5540-C sensor or in a special developer version with an extra back plug-in connector for future products evaluation. The demo evaluation kit is a simple and inexpensive testing and measuring device aimed for quick evaluation of MEAS Switzerland's flagship MS5540 pressures sensor. The evaluation kit is aimed at design engineers who need to rapidly evaluate different products from MEAS Switzerland.

Datenblatt USB Developmentkit

Sample Board
Sample Boards for the USB-Development Kit

For the following MEAS Switzerland pressure sensors sample boards for use with the USB Development kit are available. The sample boards just have to be attached to the back plug-in connector of the USB-Kit:

MS5803-XXBA, MS5607-02BA, MS5611-01BA, MS5637-02BA, MS5561, MS5805, MS5806, MS5540, MS5541

Datenblatt Sample Boards USB Developmentkit
Sample Board
PMS8607- Sampleboard with Triplesensor MS8607

The PMS8607 consists of a printed circuit board with a 4-pole pin strip, the triple sensor MS8607. Using the plug connection of the relevant pin strip the barometric pressure, humidity and temperature can be calculated with the help of a micro processor and the appropriate Software.
Sample Board
PMS5637- Sampleboard with barometer module MS5637

The PMS5637 consists of a printed circuit board with a 4-pole pin strip, the miniature barometer module MS5637. Using the plug connection of the relevant pin strip the barometric pressure and temperature can be calculated with the help of a micro processor and the appropriate Software.


Caps for Pressure Sensors

cap
Light and dust protection caps for MS5534 and MS5535 (substrate 9x9mm)

The caps serve as light protection (diffused PN-transitions of the measuring cells are UV-light sensitive) and as dust protection for the silicon coating of the measuring cell. The caps can be pressed-on the metal ring of the MS5534-CM or MS5535-CM.
cap
Light and dust protection caps for MS554x and MS5803 (substrate 6,2X 6,4mm)

The caps serve as light protection (diffused PN-transitions of the measuring cells are UV-light sensitive) and as dust protection for the silicon coating of the measuring cell. The caps can be pressed-on the metal ring of the MS554x and MS5803.
cap Light and dust protection caps for MS554x and MS5803 (Substrat 6,2X 6,4mm) with connector

The caps serve as light protection (diffused PN-transitions of the measuring cells are UV-light sensitive) and as dust protection for the silicon coating of the measuring cell. The caps can be pressed-on the metal ring of the MS554x and MS5803.


Housing

housing
89xd Plastic housing for easy assembly of ceramic pressure sensors

The sensor housing 89XD was designed to assemble ceramic pressure sensors type ME651ff, ME705 and ME501 (0..5bar and 0..10bar) to a printed circuit board in a simple and easy way. The plastic housing is suitable for pressure up to 20 bar (300psi); the pressure is applied to the sensor by a tube connector. One application for this housing is the pressure measurement in compressed air systems. Besides the two-part housing an o-ring as well as a cap nut for tube connection are included.

Datasheet 89xd
housing 90xd Stainless steel housing for prototype testing of ceramic cells

The stainless steel housing 90xd is designed for prototype testing of all available ceramic measuring cells with 18mm diameter. Additionally the housing is also suitable for the corresponding pressure transducer of the ME705 and ME707 series. The two-part housing consists of V2A steel. It is composed of the measurement cells seating, which is sealed on the pressure side by an o-ring, and a screwable overhang. The seating is designed at the outside for wrench size S24 and has a G1/4“outer thread for pressure connection. An additional thread on the opposite side of the pressure port enables the screwing of the overhang with the seating.

Datasheet 90xd


Cable

cable Connection cable for pressure sensors of the AMS 4711 and AMS 4712 series

A 3-wire cable of 2 m length with M5 sensor connector (female) series 707 from Binder GmbH is offered for an extra charge.